FuelMaster - Installation Steps Update 2010.
Please read all instructions before beginning the installation of the
FuelMaster.FuelMaster is quick and easy to install. No tools are necessary. Locate the inbound Fuel Line. Snap the 2 FuelMaster halves around the inbound fuel line. Thread the plastic ties through the slots on the sides of the unit. Tighten, making sure that the space between the 2 halves is approximately the same all around (if the fuel line is wider than the groove).
Installation Guide Which Unit to Install?
 |
Install on 3 or 4cylinder, or like sized engines |
|
|
Use on Older V6 Carbureted Engines, Motorcycles, Tractors, ATV’s
& Rec vehicles. |
|
|
Use for Home Heating systems |
|
|
Our first model has been used for 14+ years
|
|
|
Works on Diesel, Gas or Petrol fuel. |
SD FuelMaster
 |
Install on V6, V8, V10 or V12 engines |
|
|
Use on SUV's, Trucks, Sport Cars,18
Wheelers, Delivery Trucks, Buses& RV’s |
|
|
Works on Diesel, Gas or Petrol fuel |
|
|
Step up to the XL model
on bigger engines & vehicles that need the extra performance |
+++++++++++++++++++++++++++++++++++++++++++++++ Installation Steps
Installers Fingers are On Inbound Fuel Line on 4 Cyl.
To locate the inbound fuel line, find the vehicles fuel filter. The Fuel line is about the size of 1/2 a can of soup. It's usually black or silver and is most often located on the inside, left side (drivers side) of the chassis (frame). If necessary, trace the fuel lines coming out of the fuel tank. When you locate the fuel filter, install FuelMaster only on the one fuel line that comes directly out of the fuel filter, between the fuel filter and the engine (towards the front of the vehicle). The other "wrong" line is the outbound fuel line, which returns excess fuel back to the fuel tank.
FuelMaster must be installed only on the inbound fuel line that supplies fuel to the engine in order to work its fuel savings and emission reduction benefits for your vehicles.
Please Note: FuelMaster begins working as soon as the unit is properly installed upon the inbound fuel line of your car's engine, initial results may vary and will improve as you drive your vehicle over the next 600 to 1,000 miles. Optimum benefits for your individual car should be attained and level after the 1,000 driven miles. You may have a break in Period for the FuelMaster.
Install your SD or XL FuelMaster on the INBOUND TO THE ENGINE AND ATTACH THE FUELMASTER TO THAT LINE AT THE CLOSEST POINT TO THE ENGINE Always put FuelMaster after the Fuel-Filter
More Installs:
2010 V6 Front Wheel Drive Minivan Same Van Close Up 2004 V8 SUV 4x4 Same V8 Side View
Big Machines Installation Data:
Below Outlines Data for Bigger Machines: Install must be with a Mechanic assistance to insure we have installed on proper fuel lines. Each Cylinder may need a FuelMaster on that fuel injector line. So two designs happen: 1. Install the units back to back on the one main inbound fuel line to the big engine OR 2. Put one unit on each fuel injector line to each engine cylinder. As a Rule we outline baseline data below and you may need to adjust to fit the power of the machine. We do recommend only using the FuelMaster XL Model Why? It has more magnetic power to affect the fuel going into these rigs engines for Petrol or Diesel fuel. Either type of fuel can be positively affected using FuelMaster units.
Earth Moving Machines: 4 XL’s installed back to back on fuel line or one on
each Injector.
On Big Rigs or Top Kicks: Install 3 XL’s On Fuel Line Where Installers Fingers are left or on the Right picture You must install one FuelMaster XL per Injector line.
Contact
Us Email
For World Wide
Distributor Opportunities Click Here
Go To Product Pages By Clicking Links on the Names Below:
| FuelMaster | FX. Kit | Home Page | Order Now | Distributor Opportunities |
